通信设计在通信工程建设中的作用及发展思路探讨

就通信设计在通信工程建设中的重要地位进行了思考，分析了加入WTO以后我国通信设计行业面临的挑战与机遇，探讨了新形势下我国通信设计行业的应对措施及发展思路。     

High-Tc dc-SQUID magnetometer and its application in eddy current non-destructive evaluation

We have fabricated and tested a high-T_c dc-SQUID magnetometer patterned on a YBCO thin film deposited on a SrTiO₃ bicrystal substrate. The measurement of noise spectrum at 77 K showed that the magnetometer has a white noise of 333 fT/Hz^1/2 without superconducting shield, corresponding to a flux sensitivity of 14.5 μΦ₀/Hz^1/2. We constructed a test system for eddy current non-destructive evaluation of conducting aluminum plates by using the magnetometer. Flaws over 10 mm below the surface can be clearly identified. By mapping the magnetic field distribution, we can locate the flaw position. The signals caused by flaw were expanded due to the use of double-D type driving coil with a wider central slit. The experimental results confirmed that this test system could operate in a magnetic unshielded environment.     

Design optimization of radially magnetized, iron-cored, tubular permanent-magnet machines and drive systems

In this paper we deduce, from analytical field solutions, the influence of leading design parameters on the performance of a radially magnetized, iron-cored, tubular permanent-magnet machine and its drive system. We derive analytical formulas for predicting the open-circuit electromotive force, the thrust force, the iron loss, and the winding resistance and inductances, as well as the converter losses. The force density, the machine and drive system efficiencies, and the power factor and converter volt-ampere (VA) rating are established as functions of a set of machine dimensional ratios, with due account of magnetic saturation and subject to a specified thermal constraint. We validate the utility and accuracy of the analytically derived formulas by finite-element calculations. Finally, we show that the design optimization of such a linear drive system must account for the losses and VA rating of the converter as well as the design parameters of the tubular machine.     

Analysis and comparison of two-dimensional permanent-magnet arrays for planar motor

This paper investigates three kinds of permanent-magnet arrays used in planar motors with polarity centers distributed in the lattices of a matrix. The magnetic field of every kind of magnet array is analyzed by analytical methods. First, we give a Laplace equation of magnetic scalar potential and a series of boundary conditions. Then, we derive the analytical expressions of magnet field strength and magnet flux density in the air gap of each kind of magnet array by the method of separation of variables. Finally, we compare the three types of magnet arrays on the basis of the analytical solutions.     

Reduced modified quadratures for quadratic membrane finite elements

Reduced integration is frequently used in evaluating the element stiffness matrix of quadratically interpolated finite elements. Typical examples are the serendipity (Q8) and Lagrangian (Q9) membrane finite elements, for which a reduced 2 × 2 Gauss–Legendre integration rule is frequently used, as opposed to full 3 × 3 Gauss–Legendre integration. This ‘softens’ these element, thereby increasing accuracy, albeit at the introduction of spurious zero energy modes on the element level. This is in general not considered problematic for the ‘hourglass’ mode common to Q8 and Q9 elements, since this spurious mode is non‐communicable. The remaining two zero energy modes occurring in the Q9 element are indeed communicable. However, in topology optimization for instance, conditions may arise where the non‐communicable spurious mode associated with the elements becomes activated. To effectively suppress these modes altogether in elements employing quadratic interpolation fields, two modified quadratures are employed herein. For the Q8 and Q9 membrane elements, the respective rules are a five and an eight point rule. As compared to fully integrated elements, the new rules enhance element accuracy due to the introduction of soft, higher‐order deformation modes. A number of standard test problems reveal that element accuracy remains comparable to that of the under‐integrated counterparts. Copyright © 2004 John Wiley & Sons, Ltd.     

Optimization of support positions to maximize the fundamental frequency of structures

In this paper, the position optimization of simple supports is implemented to maximize the fundamental frequency of a beam or plate structure. Both elastic and rigid supports are taken into account. First, the frequency sensitivity with respect to the movement of a simple support is derived using the discrete method. By means of the shape functions of the finite element method, closed‐form sensitivity formulations are developed straightforwardly. Then, a heuristic approach, called evolutionary shift method, is presented for optimizing support positions with a fixed grid mesh scheme. Based on the design sensitivity analysis, the support with the highest efficiency is shifted in priority along the elementary edges with the interval (step) of the elementary size. To facilitate the convergence of the process, the interpolation technique is employed to evaluate the solution more accurately. Finally, three numerical examples are presented to demonstrate the validity of the sensitivity analysis and the effectiveness of the optimization method. Copyright © 2004 John Wiley & Sons, Ltd.     

Plasma spraying of nanostructured partially yttria stabilized zirconia powders

Nanosized partially yttria stabilized zirconia particles, prepared using a co-precipitation method, were reprocessed into agglomerate powders using two methods for plasma spraying. The first method was to make micrometer-sized agglomerates directly following the grinding of the calcined yttria–zirconia agglomerates. The second method was to reconstitute the nanosized particles into micrometer agglomerates using spray drying. The deposition efficiency, porosity, microhardness and average grain size of the deposits made from these two reprocessed powders were studied. Distinct results related to the process parameters were obtained for the two types of powders. The second type of powder was more suitable for plasma spraying than the first one. Using the second type of powder, some unique results distinguished from those of the conventional partially yttria stabilized zirconia powders were observed and an optimized coating with a porosity of 3.8%, Hv_0.3 of 953 and mainly consisting of 1–3 μm columnar grains in the columnar direction and smaller than 100 nm in their cross-sections was achieved.     

不确定多变量系统控制的多模型设计方法及其在造纸机控制中的应用

本文用有限个时不变模型描述不确定多变量系统,给出了一种鲁棒控制器频域设计方 法,使得由控制器和任一模型构成的单位反馈系统都达到闭环的稳定性、渐近调节和跟踪、弱 相互耦合以及期望的瞬态特性.该方法应用于造纸机的多种纸张的定量和水份控制,获得了 令人满意的效果.     

Verification of submodeling technique in thermomechanical reliability assessment of flip-chip package assembly

In this paper we verified the submodeling technique applied in the thermomechanical reliability assessment of a flip-chip BGA under accelerated thermal cycling test conditions. Since the steady-state creep model was implemented for the solder bump to better represent its realistic mechanical behavior, submodeling procedures developed specifically for path-dependent thermomechanical problems were considered. A detailed global model for the flip-chip BGA was built up to verify submodeling solutions. This model also served as a benchmark to examine solution discrepancies caused by different simplifications of the global model.